From Shipwreck to Startup: Resurrecting a Salt‑Soaked Commodore SX‑64

Retro Computing • Restoration Story

From Shipwreck to Startup: Resurrecting a Soaked, corroded, and damaged Commodore SX‑64

By Jerry L. Parker • September 24, 2025

A luggable legend that looked fine on the outside but hid a storm inside: fused screws, rotten steel, corrosion laden boards, and the long road back to that iconic blue screen.

In this article

Why I didn't walk away<br>First look: deceptive condition<br>Teardown: drilling, soaking, freeing the fused<br>Electronics: what survived and what didn't<br>Reassembly<br>Pre Power On Tests<br>Moment of truth<br>Reflections

Why I didn't walk away

I picked up the SX‑64 at the 2025 VCFSW show in Dallas, thinking the classic line: "How bad could it be?"

The gentleman who brought it to me mentioned it might have some water damage, but on the outside it looked pretty respectable, certainly no worse than others I'd seen.<br>The aluminum alloy case and plastics had held up with just minor scuffs and scratches, which made it easy to believe the machine wasn't too far gone.<br>However, the unsettling noise inside (like sand moving in a jar) told me there was more to the story.

I didn't dare power it on, but I also didn't yet realize how deep the damage went. I made an offer, the deal was done, and I<br>slid it under my table for the rest of the show before bringing it home and shelving it until a couple of weeks ago.

First look: deceptive condition

Once home, I cracked it open and the story changed instantly. All that rattling was rust flakes from the inside. The internal chassis was almost completely rotted away, screws were hopelessly fused to the frame, boards carried deposits and corrosion, and metal shields were badly eaten away. What looked like a slightly dirty portable at the show turned out to be what appeared to be a salt‑water survivor in far worse condition than I imagined.

The drive motor told the real story: inside, this machine looked more like shipwreck salvage.

Closeup of chassis and power supply damage

Extensive decay

Are the electronics ruined too?

Chassis is destroyed

You can see it is rotted through

Problem #1: the fasteners were effectively welded in place. Penetrating oil and patience weren't enough.

Teardown: drilling, soaking, freeing the fused screws.

The only way forward was mechanical. I carefully drilled out several seized screws , starting small and stepping up, keeping chips clear of the boards.<br>Brackets and shields went into rust‑removal baths where possible. In some instances, replacement was the only option, so off to<br>eBay looking for someone selling parts. Fortunately, I found a seller parting out some boards, so I emailed asking if he had any metal parts.<br>Quick negotiations and a replacement chassis was on its way! Other metal parts required attention with wire brushes and rustoleum paint to keep the rust at bay!

When chemistry fails, precision drilling wins. One screw at a time. You can see two drilled out screws here.

Plastics got a different treatment: gentle cleaning, no harsh solvents. The keyboard switches were flushed, the keycaps soaked and brushed.<br>The drive mechanism was disassembled and cleaned - but the drive motor was beyond help; anything that didn't respond to love was earmarked for replacement.

Can Plastic Rust? It certainly looked like it.

Electronics: what survived and what didn't

Corrosion on this scale is ruthless, but not everything was lost. After a careful board wash (in my dishwasher), dry (for two days), and inspection,<br>it didn't look that bad. I removed all chips from sockets, applied carefully measured doses of DeoxIT (I literally saturated the sockets and connectors<br>with the stuff), and inspected each board carefully. I was beginning to become cautiously optimistic!

Unusual step: Dishwashing the electronics.

I put the boards (and the plastics) in my dishwasher.

Reassembly

Many fasteners and screws were destroyed, so I made do with replacements from around my shop. While they aren't original, they certainly work.<br>I suspect that somewhere down the line someone will open this thing up and perhaps wonder why they are all so much different, but that's for another day.

Having secured a replacement chassis and floppy, the reassembly was relatively simple, with no surprises. It was during this process I started<br>worrying about the electronics. I hadn't tested them yet, and really didn't have any idea of what I was getting into with them. After all,<br>the work done so far had certainly been a surprise. What other surprises might be in store?

The internal assembly is complete.

New Chassis in place.

Repaired Monitor Mount Frame

Monitor, FDD Controller and Wiring.

Boards in and a splash of DeoxIT!

Just about ready to test!

Pre-Power On Testing

First, I applied mains to the power supply to test voltages.

They all measured fine so next I applied power to the monitor and watched carefully. After a few seconds,<br>the filament warmed, and the...