rz01.org

Building the QMX+ as Remote Digital Mode Station

Posted on 2026-04-24

Introduction

Over the past few months, things have somehow worked out so that I mainly operate in FM/SSB via satellite and only work digital modes on shortwave. For the latter, I had a Xiegu G90 in my shack, which was connected via about 30 meters of coaxial cable to my 10-meter-long vertical antenna in the garden, right behind the garden shed. It then occurred to me that I could easily work FT8 remotely - with the right setup. To do this, I first set up a test configuration with the two QRP Labs QDX units I already had: one for the<br>lower bands, the other for the higher bands. I connected the antenna to each of the two digimode transceivers via a coaxial relay. All this worked well so I decided to continue the mission.

Since I was in the mood for a new DIY project and like the SWR protection feature in the QMX+ (amongst other things), I ordered one of these kits. I decided not to purchase the original enclosure because, first, I can print my own, and second, I like to have a Powerpole connector for power supply in my devices.

I also decided to build the QMX+ directly with the 10W mod from PA0RDT.

The kit was delivered quickly and consisted of the following parts:

Preparing the 10W modification

First of all, I took a precision IC socket and cut it apart so that I had two sets of six pins. I soldered these to the main board and then cut two small rectangles out of a 2mm-thick sheet of aluminum; when placed one on top of the other, they fit exactly between the two socket leads and are exactly the same height as them. The idea was to ensure adequate cooling for the lower four BS 170 transistors. I made another sheet, just as wide but longer, for cooling the upper four transistors.<br>I then bent the upper four BS 170s into shape and soldered them together in parallel with the lower ones. The result looks like this:

Building the kit

Building the kit isn't exactly easy, but the instructions are excellent. The only deviation from the instructions was that, even though I chose to build the transceiver for 12V, I ended up making a 3:3 WTST instead of the RWTST intended for 12V.

There were many, many toroids to wind (a few were already soldered into the PCB):

What was much more pleasant this time compared to previous QRP Labs kits is that, instead of 0.6mm enamel-coated wire, they’ve now switched to using wire that’s only 0.33mm thick. Combined with my recently purchased Weller soldering station, I was able to solder the wire in directly and melt away the enamel with the soldering iron without having to scrape it off first.

Printing the enclosure

Fortunately, the Printables user 3DSistem has already taken the time to design a printable case for the QMX+. I want all my devices in the shack to have Powerpole connectors, which is why I’ve modified the back panel of this case slightly. First, I removed the hole for the barrel connector and added a cutout for Powerpole connectors instead. I also added two mounting holes for a step-down converter, which can be used to reduce the standard 13.8V voltage in the shack to 12V. My remix can<br>be downloaded here: QRP Labs QMX+ enclosure with Powerpole connector on Printables.com

Final assembly

When installing the circuit boards into the printed enclosure, I was able to follow the official kit instructions exactly as if it were the original enclosure, so there were no surprises. The finished transceiver looks like this:

Since the QMX+ is supposed to go in the garden shed, which has a 19" rack, I mounted all the components (switch, Raspberry Pi, QMX+, antenna tuner) on a rack shelf for an initial test setup:

This is what it looks like in the garden house rack:

Testing

First of all, I put the QMX+ into operation using a dummy load and performed various tests using the terminal application, which is accessible via the transceiver’s virtual serial interface: the audio filter sweep, RF filter sweep, image sweep, LPF sweep, and PA amplitude modulator test were all successful on the first try. The measurements of the output power per band were equally satisfactory. These matched Hans G0UPL’s measurements, with the exception that I actually managed to get 10W on 15m.

After that, I made a few test QSOs on the 40-meter and 15-meter bands. These are the bands on which my vertical antenna is resonant. The result was satisfactory despite poor band conditions:

Issues

So far, I've identified two issues that I now need to address:

The QMX+ does not turn on automatically when connected to a power source. You have to push one of the rotary encoders a little longer to turn it on. Since I want to operate the transceiver remotely, I also want to be able to turn it on and off remotely. For this, I have a Tasmota outlet that I can turn on and off via an app. I’m hoping for a firmware update that will allow me to configure the QMX+ so that it turns on automatically.

The other problem is the external...